Cart0items

Cart

Pre-Black Friday Sale : Up to 65% Off | Use code "BLACK"

Offer Expires in

  • 00
  • 00
  • 00
  • 00
0
0
Cart0items

Cart

HomeShopTesting EquipmentFluke 1507 Insulation Resistance Tester Kit – Includes FREE Products with Purchase

Description

Fluke 1507-KIT2 Offers

Ideal for advanced industrial and electrical insulation testing, this insulation tester comes in a compact design and features versatility. Additionally, the multiple test voltages facilitate the tool for many troubleshooting, commissioning, and preventative maintenance applications.

Take advantage of the full feature set to easily and quickly perform advanced insulation resistance testing. Its handy size and lightweight make it easy to pack and use. Additional features, like the remote probe, save both time and money, especially when performing repetitive tests.

Features

Rugged, compact advanced insulation resistance tester for electrical contractors and industrial and commercial electricians
Automatically calculates polarization index and dielectric absorption ratio
Makes repetitive tests simple and easy with a compare (pass/fail) function
Offers multiple insulation test voltages: 50, 100, 250, 500, and 1000 V
Performs insulation tests from 0.01 MΩ to 2.0 GΩ
Includes live circuit detection to prevent insulation test if voltage >30 V is detected
Includes auto-discharge of capacitive voltage for added user protection
Measures AC/DC voltage from 0.1 to 600 V and resistance from 0.01 Ω to 20.00 kΩ
Provides lo-ohms earth-bond continuity (200 mA)
Simplifies repetitive or hard-to-reach testing with the remote test probe
Saves battery power with auto power off
Presents results on a large, backlit display
Features CAT IV 600 V over voltage category rating
Runs on four AA alkaline batteries (NEDA 15 A or IEC LR6) for at least 1000 insulation tests

Applications

Troubleshooting
Commissioning
Preventative maintenance

REED R2300 Infrared Thermometer
This infrared thermometer features a 12:1 distance to spot ratio and is capable of measuring temperatures up to 752°F (400°C). The R2300 is an affordable non-contact measurement solution able to quickly and efficiently measure the temperature of hot, hazardous or hard-to reach objects from a safe distance.

Features

Built-in laser pointer identifies target area
User selectable °F or °C
12:1 distance to spot size ratio
Digitally adjustable emissivity
Max and Min readings
Backlit display
High and low alarms
Low battery indication and auto shut off

REED R5110 Non-Contact Voltage Detector with Flashlight

This Voltage Detector has the ability to detect the presence of AC voltage from a safe distance. The R5110 features two voltage ranges allowing it to detect both high (90 to 1000V) and low (24 to 1000V) AC voltage wiring.

Features

Suitable for receptacles or against insulated wire
Double insulated housing for increased safety
Audible (buzzer) and visual (LED) indicators
Built-in flashlight
Pocket clip
Auto shut off
Cat. IV 1000V safety rating

6 Tips for effective insulation testing

1

Disconnect any electronic devices like motor drives, PLC’s, transmitters, etc. before performing insulation testing. Electronics can be damaged by applying higher than normal voltage.

2

The effect of temperature should be considered – it is recommended that tests be performed at a standard conductor temperature of 20 °C (68 °F) or that a temperature baseline is established while compensating future readings by using a DMM with a probe or an infrared thermometer.

3

Select a test voltage appropriate for the insulation being tested. The objective is to stress the insulation but not to over-stress it. When in doubt, use a lower test voltage. It’s usually appropriate to test insulation at twice the voltage it normally sees: for example 460 V to 600 V rated equipment is often tested at 1000 V.

4

When using an insulation tester, leave the leads connected when you stop the test. The insulation tester can discharge any residual test voltage.

5

Conductors that are close to each other have a normal capacitance. This will cause an insulation resistance reading to start low and increase steadily until it stabilizes. This type of increase is normal, but if the reading jumps violently down and up again this indicates arcing.

6

Although the current is tightly limited, an insulation tester can generate sparks and minor but painful burns. The unexpected surprise can cause an operator to jerk away. As always, work away from live systems and use safe work practices when working overhead.

Insulation Resistance Testing SolutionsFluke 1507-KIT2 Offers

Ideal for advanced industrial and electrical insulation testing, this insulation tester comes in a compact design and features versatility. Additionally, the multiple test voltages facilitate the tool for many troubleshooting, commissioning, and preventative maintenance applications.

Take advantage of the full feature set to easily and quickly perform advanced insulation resistance testing. Its handy size and lightweight make it easy to pack and use. Additional features, like the remote probe, save both time and money, especially when performing repetitive tests.

Features

Rugged, compact advanced insulation resistance tester for electrical contractors and industrial and commercial electricians
Automatically calculates polarization index and dielectric absorption ratio
Makes repetitive tests simple and easy with a compare (pass/fail) function
Offers multiple insulation test voltages: 50, 100, 250, 500, and 1000 V
Performs insulation tests from 0.01 MΩ to 2.0 GΩ
Includes live circuit detection to prevent insulation test if voltage >30 V is detected
Includes auto-discharge of capacitive voltage for added user protection
Measures AC/DC voltage from 0.1 to 600 V and resistance from 0.01 Ω to 20.00 kΩ
Provides lo-ohms earth-bond continuity (200 mA)
Simplifies repetitive or hard-to-reach testing with the remote test probe
Saves battery power with auto power off
Presents results on a large, backlit display
Features CAT IV 600 V over voltage category rating
Runs on four AA alkaline batteries (NEDA 15 A or IEC LR6) for at least 1000 insulation tests

Applications

Troubleshooting
Commissioning
Preventative maintenance

REED R2300 Infrared Thermometer
This infrared thermometer features a 12:1 distance to spot ratio and is capable of measuring temperatures up to 752°F (400°C). The R2300 is an affordable non-contact measurement solution able to quickly and efficiently measure the temperature of hot, hazardous or hard-to reach objects from a safe distance.

Features

Built-in laser pointer identifies target area
User selectable °F or °C
12:1 distance to spot size ratio
Digitally adjustable emissivity
Max and Min readings
Backlit display
High and low alarms
Low battery indication and auto shut off

REED R5110 Non-Contact Voltage Detector with Flashlight

This Voltage Detector has the ability to detect the presence of AC voltage from a safe distance. The R5110 features two voltage ranges allowing it to detect both high (90 to 1000V) and low (24 to 1000V) AC voltage wiring.

Features

Suitable for receptacles or against insulated wire
Double insulated housing for increased safety
Audible (buzzer) and visual (LED) indicators
Built-in flashlight
Pocket clip
Auto shut off
Cat. IV 1000V safety rating

6 Tips for effective insulation testing

1

Disconnect any electronic devices like motor drives, PLC’s, transmitters, etc. before performing insulation testing. Electronics can be damaged by applying higher than normal voltage.

2

The effect of temperature should be considered – it is recommended that tests be performed at a standard conductor temperature of 20 °C (68 °F) or that a temperature baseline is established while compensating future readings by using a DMM with a probe or an infrared thermometer.

3

Select a test voltage appropriate for the insulation being tested. The objective is to stress the insulation but not to over-stress it. When in doubt, use a lower test voltage. It’s usually appropriate to test insulation at twice the voltage it normally sees: for example 460 V to 600 V rated equipment is often tested at 1000 V.

4

When using an insulation tester, leave the leads connected when you stop the test. The insulation tester can discharge any residual test voltage.

5

Conductors that are close to each other have a normal capacitance. This will cause an insulation resistance reading to start low and increase steadily until it stabilizes. This type of increase is normal, but if the reading jumps violently down and up again this indicates arcing.

6

Although the current is tightly limited, an insulation tester can generate sparks and minor but painful burns. The unexpected surprise can cause an operator to jerk away. As always, work away from live systems and use safe work practices when working overhead.

Insulation Resistance Testing Solutions

Fluke 1507-KIT2 Specifications

AC/DC Voltage Specifications

Range
600.0 V

Resolution
0.1 V

Accuracy
50 Hz to 400 Hz: ±(2% of rdg + 3 digits)

Input Impedance
3 MΩ (nominal), < 100 pF Common Mode Rejection Ratio (1 kΩ unbalanced) >60 dB at DC, 50 or 60 Hz

Overload Protection
600 V RMS or DC

Earth Bond Resistance Specifications

Range
20.00 Ω to 20.00 kΩ

Resolution
0.01 Ω to 0.01 kΩ

Accuracy
±(1.5% + 3 digits)

Overload Protection
2 V RMS or DC

Open Circuit Test Voltage
>4.0 V, <8 V Short Circuit Current >200.0 mA

Insulation Specifications

Measurement Range
0.01 MΩ to 10 GΩ

Test Voltage
50, 100, 250, 500, 1000 V

Test Voltage Accuracy
+20%, -0%

Short Circuit Current
1 mA nominal

Auto Discharge
Discharge time <0.5 second for C = 1 µF or less Live Circuit Indicator Inhibit test if terminal voltage >30 V prior to initialization of test

Maximum Capacitive Load
Operable with up to 1 µF load

Live Circuit Detection
Inhibit test if terminal voltage > 30 V prior to initialization of test

Maximum Capacitive Load
Operable with up to 1 µF load

Measure Accuracy
50 V: ±(3% + 5)

100 V: ±(3% + 5)

250 V: ±(3% + 5)

500 V: ±(3% + 5)

1000 V: ±(3% + 5) to 2000 MΩ, ±(10% + 3) above 2000 MΩ

Click here for complete specifications on the Fluke 1507-KIT2

This Fluke 1507-KIT2 Insulation Tester Kit Includes

Fluke 1507 Insulation Tester

Save time with the automatic calculation of polarization index and dielectric absorption ratio. Capable of reading resistance from 0.01 Ω to 20.00 kΩ.

REED R2300 Infrared Thermometer

Fast responding entry-level infrared thermometer with min/max temperature readings and adjustable high/low temperature alarms.

REED R5110 Non-Contact Voltage Detector with Flashlight

AC Voltage Detector with built-in flashlight and pocket clip.

What’s included with the Fluke 1507-KIT2
Insulation Resistance Tester
Remote Probe
Test Leads
Test Probes
Alligator Clips
User Documentation

Two in one tools
Stand-alone tools

Insulation test features

1587 FC
1577
1503
1507
1550C
1555

Test voltages

50 V, 100 V, 250 V, 500 V, 1000 V
500 V, 1000 V
500 V, 1000 V
50 V, 100 V, 250 V, 500 V, 1000 V
250 V to 5000 V
250 V to 10,000 V

Insulation resistance range
0.01 MΩ to 2 GΩ
0.01 MΩ to 600 GΩ
0.01 MΩ to 2000 GΩ
0.01 MΩ to 10 GΩ
250 kΩ to 1 TΩ
250 kΩ to 2 TΩ

PI/DAR

Auto discharge

Timed ramp test (Breakdown)

Pass/fail comparison

Est. # of IRT tests

1000
1000
2000
2000
Various
Various

Voltage > 30 V warning

Memory

With Fluke Connect App

Remote test probe

Lo ohms/earth-bond continuity

200 mA source (10 mΩ resolution)
200 mA source (10 mΩ resolution)

Display

Digital LCD
Digital LCD
Digital LCD
Digital LCD
Digital LCD/ analog display
Digital LCD/ analog display

Hold/lock

Multimeter features

AC/DC volts

Note: Not all product features and specifications are listed in this table. For more complete information, see individual product data sheets.
Footnotes:

1. Function useful for checking connections and motor windings. Also useful for users who are required to perform earth-bond continuity measurements during installation testing.
2. Filter for variable-speed motor drive measurements.

Current

Resistance

Continuity beeper

Temperature (contact)

Lo-pass filter2

Capacitance

Diode test

Frequency

MIN/MAX

Other features

Backlight

Software

Fluke Connect compatible

FlukeView® Forms Basic
Fluke View® Forms Basic

Battery

4 AA (NEDA 15A or IEC LR6)
4 AA (NEDA 15A or IEC LR6)
4 AA (NEDA 15A or IEC LR6)
4 AA (NEDA 15A or IEC LR6)
Rechargeable
Rechargeable

Find out more about insulation testing

Webinar: Facilities Maintenance with Fluke

Proactive maintenance and energy savings strategies are essential for cost savings in facilities.

We’ve teamed up with Fluke to provide you with a thorough discussion on proactive maintenance strategies – approaches, tools, and the proper “health” measurements on critical assets. As managing energy costs are also critical, we will also explore how implementing an onsite compressed air and gas leak detection program, facilities can save tens of thousands of dollars annually and production equipment downtime. The latest test equipment advances have made it possible for users to perform leak inspections with little to no training in a fraction of the time versus conventional tools.

During this short webinar on Facilities Maintenance, we covered:Monitoring critical assets with fewer resources Bridging the skills gapWhy are we replacing the same bearings and seals over and over?What are the best tools to use? How do we justify the cost of the tools and resources?How do we start a Proactive Maintenance program?

How to Operate a Fluke 1507 Insulation Resistance Tester to Run PI and DAR Test

This video covers the difference between the polarization index and dielectric aspect ratio tests when using the insulation resistance tester. With their multiple test voltages, this tool makes it ideal for many troubleshooting, commissioning, and preventative maintenance applications.

Reviews

There are no reviews yet.

Be the first to review “Fluke 1507 Insulation Resistance Tester Kit – Includes FREE Products with Purchase”

Your email address will not be published. Required fields are marked *

Select your currency